CP-01
Rotary Compressor
Single-cylinder rotary with suction accumulator, for wall-mounted split units.
We supply AC and refrigeration spares from our shop in Jamia Nagar, New Delhi.
Most of the people who walk in are technicians and contractors in the middle of a job. They need a compressor, a cylinder of gas, a few metres of copper or a capacitor, and they need it today. That is what we keep in stock.
This site shows the kinds of products we carry. It is not a shop, so there are no prices here. Call us or send an email and we’ll tell you what’s available.
Read more about usRotary, scroll, reciprocating and screw compressors, plus condensing units.
CP-01
Single-cylinder rotary with suction accumulator, for wall-mounted split units.
CP-02
Sealed piston type for display coolers and small condensing units.
CP-03
Vertical scroll for ducted, packaged and light commercial systems.
CP-04
Bolted, serviceable body for cold storage and process cooling.
CP-05
Twin-screw unit for large chillers and continuous-duty plants.
CP-06
Variable-speed rotary for inverter split air conditioners.
CP-07
Belt-driven compressor with clutch pulley for car and van air conditioning.
CP-08
Belt-driven reciprocating unit with flywheel, for ammonia and transport duty.
CP-09
Two scrolls on one rail with shared manifold, for staged capacity.
CP-10
Air-cooled unit with compressor, receiver and fans for cold rooms.
Refrigerant gas, nitrogen for testing, recovery cylinders and brazing gases.
CY-01
Disposable cylinder for servicing older split and window units.
CY-02
High-pressure blend for ducted, VRF and modern split systems.
CY-03
Propane-grade hydrocarbon in a returnable cylinder.
CY-04
Dry nitrogen for pressure testing and brazing purge.
CY-05
Refillable cylinder for recovering refrigerant from a system.
CY-06
Oxygen cylinder with valve for oxy-fuel brazing and cutting.
CY-07
Dissolved acetylene, the fuel gas for oxy-acetylene brazing.
CY-08
Refillable LPG cylinder, a common fuel for brazing torches.
CY-09
Oxygen and acetylene cylinders with regulators, hoses and torch on a trolley.
CY-10
Two-gauge brass regulator to control cylinder pressure.
Outdoor, indoor and exhaust motors with the blowers and blades that go on them.
FM-01
Outdoor unit motor with mounting studs and lead wires.
FM-02
Squirrel-cage blower assembly for ducted and cassette units.
FM-03
Compact open-frame motor for coolers and small fans.
FM-04
Permanent split capacitor motor with cradle base.
FM-05
Centrifugal fan that fits inside round ducting for extraction and fresh air.
FM-06
Four-blade axial fan on a spider bracket for condensers.
FM-07
Brushless DC motor with on-board controller for inverter units.
FM-08
Square-frame exhaust fan with guard for kitchens and plant rooms.
FM-09
Small motor and blade on bracket for fridges and display chillers.
FM-10
Shaft on both ends with resilient mounts, for twin-blower units.
Soft and hard drawn copper, insulated pipe, fittings and valves.
CU-01
Soft annealed copper in a flat coil, cut to length on site.
CU-02
Hard drawn lengths for risers, headers and plant room runs.
CU-03
Copper pipe in foam insulation, to stop heat gain and sweating.
CU-04
Short-radius elbow for brazed turns in refrigerant lines.
CU-05
Equal tee for branching suction and liquid lines.
CU-06
Brass ball valve with lever handle for quick shut-off.
CU-07
Steps a line down from one pipe size to the next.
CU-08
Forged flare nuts in the usual service sizes.
CU-09
Fine-bore copper metering tube sold by the coil.
CU-10
Mixed solder fittings: elbows, tee, coupler, reducer and end cap.
What a technician carries from one job to the next: gauges, pumps, pipe tools and hand tools.
TL-01
Twin gauges with sight glass and three charging hoses.
TL-02
Two-stage pump with oil sight glass for evacuating systems.
TL-03
Adjustable spanner for flare nuts, valves and fittings.
TL-04
Roller cutter for square, burr-free copper cuts.
TL-05
Lever bender that turns copper without kinking it.
TL-06
Side cutters with wire stripper for electrical work on units.
TL-07
Ratchet, sockets and bits for panels, brackets and mounting bolts.
TL-08
Measures current, voltage and resistance on site.
TL-09
Metric hex keys in a fold-out holder, for fan blades and set screws.
TL-10
Gas torch for brazing copper joints on site.
Capacitors, controls and valves: the small parts that stop a system when they fail.
PT-01
Round can capacitor serving compressor and fan together.
PT-02
Gives single-phase motors the extra torque to start.
PT-03
Switches compressor and fan power from the control circuit.
PT-04
Wall-mounted temperature controller with display.
PT-05
Meters refrigerant into the evaporator against superheat.
PT-06
Dial pressure gauge in bar and psi for chiller and water lines.
PT-07
Brass valve with service port at the outdoor unit.
PT-08
Disc protector that trips the compressor on heat or current.
PT-09
Adjustable cut-out for high or low pressure.
PT-10
Coil-operated valve for liquid line shut-off.
Looking for a part you don’t see here? We carry a lot more than what’s on this website.